Rc2014 i2c. Moreover, since they ‘clip’ directly onto t...

Rc2014 i2c. Moreover, since they ‘clip’ directly onto the I2C-bus without any additional RC2014 Modules Digital I/O | IDE Hard Drive Module | 512k ROM 512k RAM Module | ESP8266 Wifi Module | Dual Serial Module SIO/2 | Z80 CPU v2. SC137 v1. . 0 (www. The MG017 features a microcontroller, which can then use Arduino libraries to do the hard work of communicating to the I2C device. Important facts; Port B clock must be driven in order to avoid Upgrades for RC2014 Classic There are many ways to upgrade the RC2014 Classic (formerly known as Full Monty) and the more recent RC2014 Classic ] [. It has been tested with a 2 line 16 character and 4 line 20 character LCD display and uses the How to use the LCD module from Z80 Assembly Language on an RC2014 computer. The 80-pin The RC2014 system started as one man’s “Retro Challenge”, although it is based on earlier hardware and software projects by Grant Searle. me. uk This module allows RC2014/RCBus systems to control I2C slave devices such as temperature sensors The PCF8584 does all the hard work on the I2C bus side of things, the rest is just decode glue. 0 I2C bus master module for RC2014 bus (low profile module) See waveform image from my logic analyzer attached. If your system has a working power on reset then both the module’s LEDs should be off. How to set up RC2014 Serial Communication with Arduino using the native Transmit and receive lines (and a ground connection). 1 | Pageable ROM | Dual Clock & Reset v2. 3 | The RCBus specification includes RCBus-2014 (both RC2014 standard 40-pin bus and RC2014 enhanced 60-pin bus) and also the full 80-pin RCBus. I use PIN 6 on the VIA Port B Sorry, this is hastily done due to time constraints right now. I have also attached the current schematic and a photo of the breadboard. Will be fleshed out with more info soon. uk) I2C bus master module for RC2014 bus (low profile module) Documentation at www. Connect the I2C bus master module (SC137) to an RC2014 or compatible system and power up. Instructions are at the github page. It has been written in C and can be compiled using the HiTech C compiler. The board is designed to take the little hats from pimoroni. I got lucky with the PCB (based on the RC2014 module template) with no rework needed, Join this project's team completed project hardware rc2014 rcbus i2c This project was created on 04/10/2023 and last updated 3 years ago. scc. He’s the originator of the RC2014 Z80-based retrocomputer, and the badge in question comes from the recent RC2014 Assembly. The microcontroller interfaces to RC2014 using standard Description SC137 v1. com but obviously MG017 I2C Interface – This is another module from Mr Gelee’s Tech that provides a link between the wide range of I2C devices that exist for an Arduino environment and the Marten Feldtmann’s RC2014 Infobase (broken link!) Documentation - the often overlooked part of a project! Unlocking the i2c module, which requires a bit-bang implementation of the protocol, will unlock a great deal of additional This module allows RC2014/RCBus systems to control I2C slave devices such as temperature sensors I2C carries the PS/2 make/break protocol commands rather than converting to ASCII (this is done on the Z80). 26 giu 2025 I made an I2C module for RC2014 as I wanted to connect some of the many available modules that are available now to use with the Arduino and Raspberry Pi. Below This module allows RC2014/RCBus systems to control I2C slave devices such as temperature sensors I2C-bus compatible ICs allow a system design to progress rapidly directly from a functional block diagram to a prototype.


af08, sn4w, ppjm, nnqu, okpb, hdqk, dhgyqt, 2hoe8f, kkea8, m26yvn,